MAGIC® APPLICATION GUIDE
DMiBOP10X REINFORCED WET STRENGTH INDOOR/OUTDOOR INKJET
BANNER PAPER FOR XEROX XPRESS & ECO SOLVENT PRINTERS
magic
MAGIC® DMiBOP10X is an economical alternative for short-term, indoor promotional banner applications where high tear strength is not required. DMiBOP10X can also be used in indoor wallcovering applications. If outdoor use is desired, the material can be posted onto a rigid surface to prevent environmental or wind-induced tears. Latex saturation and nylon make it more than just a wet strength paper!


PHYSICAL PROPERTIES
30/60 %
3%
2 months
6 months
20-60%
70°F (21°C)
Class A**
Ultimate Elongation (MD/CD
Wet Expansion
Outdoor Life Expectancy*
Indoor Life Expectancy*
Optimum Print RH
Optimum Print Temp
Flame Spread Classification
6.7 oz/yd² (228 g/m²)
11 mil (280 microns)
97%
104
95
52/33 lbs/in
Basis Weight
Caliper
%Opacity
Whiteness
Brightness
Tensile Strength (MD/CD)

*Based on manufacturer's accelerated age testing. Lamination will increase life expectancies. Results may vary based on usage. **Based on ASTM E84 test method

APPLICATION GUIDELINES
Outdoor and Indoor Banner:
This product is recommended for only indoor banner applications.

Printer & Ink Compatibility:
DMiBOP10 can be printed on Xerox Xpress, X2, Roland Soljet, and Mutoh Falcon Outdoor printers equipped with pigmented inks. Dye-based inks are not recommended.

Water Resistance & Surface Protection:
To obtain a high degree of water resistance, use only pigmented ink. Lamination is not required. Ink coverage of up to 250% is recommended, because higher ink saturation can affect the waterfast properties and show ink bleed in heavy saturation areas. Let the image dry 24 hours before exposing to moisture. Dirt and stains can not be cleaned from the imaged surface and the surface can be damaged from excessive folding or creasing, so overlaminating is recommended to help protect it.

Printing Guidelines:
To optimize print quality, printers should be set for highest print quality. Due to the heavy gauge of the material, this product can feed through the printers at different rates causing print size to vary slightly from print to print. Images sized in a software application may be printed slightly smaller then anticipated.

Material Handling & Storage:
Once the print is completed, roll imaged media onto a core until ready for posting. Folding of the material is not recommended. After use, the material should be stored in its original packaging in the poly bag suspended on the end boards. The material should be stored a 72°F (+/-5°) for no more then 1 year.

FINISHING RECOMMENDATIONS
Wallcovering:
Refer to the inkjet wallcovering technical bulletin for complete wallcovering guidelines.

Banner Installation:
Improper installation can cause pre mature banner failure. It is recommended that a professional installer be used.

Tape & Stitched Hem:
Standard high-tack banner tape can be used and is preferred to sewing, as the sewing process can scratch or cause coating pick-off. Follow the guidelines of the tape manufacturer. If sewing, it is recommended that the unlaminated banners be stitched hem side up so that the sewing machine foot comes in contact with only the backside of the banner. For maximum reinforcement, a double-stitched hem with a double lock stitch, with a maximum of five stitches per inch and corner reinforcements are recommended.

Grommeting:
Grommets should be placed in the hemline along the length of the banner so that the grommet is through two layers. Corner grommets should be placed where the length and width hems cross, so that the grommet is through four layers. A reinforced corner is also recommended to increase durability.

Laminating:
Magic Fluorex® Transfer Protection - DMFTP - ultra thin (3 micron), graffiti-resistant overlaminate, is an ideal solution for banner materials. A vinyl pressure-sensitive overlaminate is recommended. However, overlaminating one side may cause the product to curl toward the laminated side. Let image dry 24 hours before laminating.
www.ppmsupplies.nl