MAGIC® APPLICATION GUIDE
DMVLA5X MATTE PRESSURE-SENSITIVE INK JET VINYL
FOR XEROX XPRESS & ECO SOLVENT PRINTERS
magic
MAGIC® DMVLA5X is a white opaque, matte, calendered vinyl with a permanent pressure-sensitive adhesive. Excellent for printing flexible, durable signs and banners, DMVLA5X results in broad color gamut and superior waterfastness with pigmented inks when used in Xerox Xpress and eco-solvent printing systems.


PHYSICAL PROPERTIES
339 g/m² (9.9 oz/yd²)
190 g/m² (5.6 oz/yd²)
Permanent Solvent
3.5 lb/in
0.9 %
Class B
70°F (21°C)
6 months
6 months
Basis Weight (w/liner)
Basis Weight (no/liner)
Adhesive
Adhesive peel force on stainless steel
Dimensional stability
Flame spread classification (ASTM E84)
Optimum Print Temperature
Indoor Life Expectancy*
Outdoor Life Expectancy*
Calendered
3.5 mil (89 microns)
5 mil (127 microns)
13.5 mil (344 microns)
93%
82
92
2.1

Vinyl Type
Caliper of Vinyl
Caliper of Vinyl/Adhesive
Total Caliper
%Opacity
Whiteness
Brightness
Gloss (60°)

*Based on manufacturer's accelerated age testing using pigmented ink. Results may vary based on usage.


APPLICATION GUIDELINES
Printer & Ink Compatibility:
DMVLA5X can be printed on Xerox Xpress, X2, Roland Soljet, and Mutoh Falcon Outdoor printers equipped with pigmented inks. Dye-based inks are not recommended.

Outdoor and Indoor Use:
This product is recommended for indoor and outdoor applications. It must be applied at minimum air and surface temperatures of 50°F. Once posted, the material can withstand temperatures of 0°F to 150°F.

Water Resistance & Surface Protection:
To obtain a high degree of water resistance, use only pigmented ink. Lamination is not required. Let image dry 24 hours before exposing to moisture. Dirt and stains cannot be cleaned from the imaged surface. Excessive folding or creasing can damage the imaged surface. Laminating is recommended to protect the surface from dirt and abrasion.

Printing:
Ink coverage of up to 250% is recommended. Excessive ink saturation can affect the waterfast properties of the material as well as color uniformity. To optimize print quality, printers should be set for highest print quality.

Color Calibration:
ICC color profiles can be obtained for selected RIP, ink and printer combinations.

Material Handling & Storage:
Once print is completed, roll imaged media onto a core until ready for posting. Folding of the material is not recommended. Unimaged material should be stored at 72°F (+/-5°) for no more than 6 months, to obtain maximum adhesion values. After use, the roll should be stored in its original packaging in the poly bag.


FINISHING RECOMMENDATIONS
Recommended Application Surfaces:
Stainless steel, aluminum, glass, ABS, polycarbonate, Plexiglas®, automobile enamel and standard mounting boards like Sintra, Gatorfoam® and Foam-Core. The product is designed for use on smooth, flat surfaces and should not be applied over corrugations or rivets. Textured surfaces and wood tend to promote poor adhesion. Always pretest your specific substrate prior to actual application.

Surface Preparation:
Always ensure that the receiving substrate is thoroughly cleaned, free of dust, dirt or cleaner residues. Painted surfaces should latex paint containing no waxes or silicones. Metal and glass surfaces can be cleaned with standard glass cleaners. Poor surface conditions will cause adhesion loss or failure.

Application Paper (Premask):
Use low tack application tapes. High tack tapes can cause slight coating removal. Application paper applied directly onto the imaged surface of the vinyl may cause slight yellowing of the coating. The premask by American Biltrite Inc. called TransferRite®, cause the least amount of yellowing. 3M tapes have been found to increase the yellowing effect.

Installation Techniques:
Proper contact of the adhesive to to mounting substrate is critical and maximum pressure should be used to install the vinyl. If insufficient pressure is used during the install, the edges of the vinyl can lift. When applying vinyl to mounting boards, it is recommended that a cold roll laminator be used to give adequate, even pressure during application. For installations by hand, use application tape and squeegee with adequate pressure. It is recommended that water not be used during the installation but if it is used, use minimal amounts. All water must be squeegeed out from under vinyl. If liquid soap is added to the water to increase the ease of installation, use only one drop per gallon of water. Soap must not contain moisturizer. Do not use heat guns to install vinyl. Material should not be stretched during installation. It is a calendered vinyl, and it will shrink back to original size, which might cause edges to lift or create gaps between panels.

Laminating:
To give surface protection from dirt and abrasion, a vinyl pressure-sensitive overlaminate is recommended. Heat activated laminates should not be used. The high temperatures needed to apply heat activated laminates can degrade the adhesive peel strength. Overlaminating one side with too much tension can cause the product to curl toward the laminated side and the edges to lift. Magic's DMFTP Fluorex® Transfer Protection, ultra-thin (3 micron) graffiti-resistant overlaminate, is an alterative finishing solution. Let image dry for 24 hours before laminating.

Removal:
The adhesive is very aggressive and removal may cause damage to indoor painted surfaces or drywall surface. To increase the ease of removal, gently heat the vinyl with a heat gun to soften the vinyl and adhesive. The longer DMVLA5X is applied, the more difficult the removal will be. Different surfaces will have different adhesion characteristics. Glass and stainless steel usually promote extremely high adhesion values and removal may be more difficult than with other surfaces. If during the removal, adhesive transfer happens, soapy warm warm water and aggressive rubbing with a cloth should remove adhesive. For surfaces with more difficult adhesive removal, isopropyl alcohol (a.k.a.- IPA or rubbing alcohol) can be used.
www.ppmsupplies.nl