

TECHNICAL DATA SHEET JT 5929 BF MACTAC
Self-adhesive Digital Imaging Media for wide-format solvent-based & UV inkjet Printing.
Self-adhesive Digital Imaging Media for wide-format solvent-based & UV inkjet Printing.
JT 5929 BF
7 year polymeric calendered vinyl
PRODUCT DESCRIPTION:
Face material : 70μ White gloss polymeric stabilised, soft calendered PVC film.
Micro-structured repositionable permanent opaque acrylic.
Coated Kraft liner 140 gsqm backprinted MACtac in red.
Micro-structured repositionable permanent opaque acrylic.
Coated Kraft liner 140 gsqm backprinted MACtac in red.
Face material :
Adhesive :
Liner :
Adhesive :
Liner :
TYPICAL USES:
Long term outdoor, advertising or promotion on flat or curved surfaces.Product benefits : dry application at it's best!
A patented performance feature enabling the Applicator of the printed decal to apply much faster and to limit the risks of wrinkles and entrapped air bubbles generally associated with the application of large format decals. BF series therefore save time by increasing productivity during the application job. The micro-structured repositionable adhesive system allows the installer to remove and re-apply the decals during the job. It is possible to press out small entrapped air bubbles with ease!
As a result : A great looking job!
PRINTING
Especially designed for solvent based & UV inkjet printing on wide-format printing equipment. To achieve the best possible print quality, please make sure that the correct ICC profiles or printer settings are used.Important notice: It is CRITICAL that any digital prints are TOTALLY DRY before application. While this is important for all films in the JT 5000 range it is even more important for the special tack system of JT 5929 BF. If the film is not dried sufficiently the vinyl and adhesive will still be full of solvents which change the properties and consequently the behaviour of the film. The customer will therefore not benefit from the bubble free effect enough to reduce application time. It can also cause adhesive residue to be left behind and lack of repositionnability. This is also important when laminating the printed decal.
PHYSICAL PROPERTIES OF THE UNPRINTED FILM:
Test method
FTM 9
FTM 1
FTM14
Average values
18 ± 3 N/25mm
17 ± 3 N/25mm
max 0.5%
+ 10°C
-20°C to +70°C
Adhesive Data, 23°C
Quick Tack on glass
Peel 24 hours on glass
Dimensional stability
% Shrinkage 48 h at 70°C
(applied on aluminium)
Temperature ranges
Minimum application temperature:
Service temperature range
SHELF LIFE:
2 years when stored at 15/25°C and 50% relative humidity (in the original packaging).DURABILITY:
The outdoor durability of the unprinted film is 7 years. Overlamination of the inkjet printed material delays eventual colour fading that may occur upon time. This colour fading is dependent from the quality of the inkjet inks and the self-adhesive materials being used.RECOMMENDATIONS:
Always test your combination of JT5000 products, inks and laminating films prior to commercial use.- Printing conditions:
A conditioned pressroom, ± 23°C and 50% RH. - Laminating conditions:
Please ensure the print is perfectly dry. The printed material should be left to dry for at least 48h prior to lamination or transport. Additional hot air drying or IR drying will speed up the drying process and shorten the overall drying time. If the printed graphics is likely to be exposed to corrosive liquids, smokes, fumes, highly polluted areas or if there is a likelihood of scratching or friction or to ensure longer durability, it is strongly recommended to laminate the prints with pressure sensitive protective films IMAGin LF3999 (glossy) or LF 3898 (matt). - Transportation Conditions:
To allow easy transportation, IMAGin JT series can be rolled up, with the image on the outside, with a minimum diameter of 15 cm (for example on a 6″ core). When the image is not protected with a laminating film, make sure that the print is perfectly dry before rolling it over. To avoid exposing the print to any liquid aggressions, prints should be protected by a plastic bag. During the transport or storage of the prints, avoid exposing them to extreme temperature and humidity variations.
GENERAL REMARK: factors affecting adhesion
To ensure application suitability - always test the proposed construction under actual application and end-use conditions before going into full production. The following factors will adversely affect adhesion of a pressure-sensitive adhesive:- Dusty, dirty, oily or oxidized surfaces
- Mould release agents on blow-moulded plastic surfaces
- Low surface energy substrates, such as: polyethylene, polypropylene...
- Application below the minimum application temperature or use outside of the recommended service temperature ranges.
IMPORTANT NOTICE:
All MACtac products are subject to careful quality control throughout the manufacturing process and are warranted to be of merchantable quality and free from manufacturing defects. Published information concerning MACtac products is based upon research which the Company believes to be reliable although such information does not constitute a warranty. Because of the variety of uses of MACtac products and the continuing development of new applications, the purchaser should carefully consider the suitability and performance of the product for each intended use, and the purchaser shall assume all risks regarding such use. The seller shall not be liable for damages in excess of the purchase price of the product nor for incidental or consequential damages. All specifications are subject to change without prior notice.
www.ppmsupplies.nl